Q1. Given the following setup code for Timer 2, write an Interrupt Service Routine (ISR) for Timer 3 that uses INV to toggle the LED light connected to Port A, RA5. The ISR should be called Timer3Interrupt. Timer 3 setup: Internal fPB clock is 40Mhz , pre-scalar 1:256
Q2. a) If TAD = 85 * 10-9 (85 ns) Seconds (Assume PBclk-Freq = 40 MHz , [2 Marks] So TPB = 1 PBclk − Freq ), Calculate the ADC’s value. Hint: TAD = 2 * (TPB * (ADCs + 1)) b) Write the following Setup code for the ADC with manual sampling and manual conversion.
Q3a.Write a program using an Interrupt Service Routine that does the following : Waits for a Single High Pulse of 250 ms on Pin OC3. When the High Pulse goes from High to low , it turns ON the LED at Port A, RA3 and the LED then stays on. You will use the Output Compare OC1, Dual Compare mode with a Single High Pulse (OCM= 004). You will use Timer 3 for the OC with a pre-scale value of 256. You need to setup OC3RS and OC3R such that OC3RS – OC3R = 200 ms. We need to convert 200 ms into Timer Clock Cycles. We have Timer 3 with a fpb is 10 Mhz and a Precale of 1:64.
Category: Electrical Engineering
PLEASE DON’T USE CHEGG OR CHATGPT TO GET THE ANSWER. this is very important assignment for me and my grade depends on it
I am uploading my previous work. New task is related to previous work.
Further evaluation needed on my previous work using ansys by meshing
My previous file is 6508ENG_Project proposal.
Also I have added RUBICS.
Need minimum of 90%. Need maximum effort for this, PLEASE.
PLEASE PAY ATTENTION TO THE NOTES BELOW!
I. To maximize partial credit, show all your work in a clear and concise fashion.
II. Points are proportional to the difficulty of the questions. More weighting will be given to
plotting parts of questions.
III. Labels are equally as important as the plot shape itself. Calculations are there as backup in case
of wrong or messily written plots.
V. Justify and discuss require some degree of logical and/or mathematical explanation. Plots
without any such explanation will not receive full credit.
Problem Scores are as follows:
1 ___/25
2 ___/25
3 ___/25
4 ___/15
5 ___/10
Needs to be done perfectly with at least 90% credit, and your own clean perfect work
Research Problem Statement
design non traditional communication device (ESP32 inside the Key Fob ) Using encrypted bluetooth channel . Consider SD card connected the esp32 to store and transfaer the message Based on your submission for the research problem statement, please do the following:
Identify your current or proposed research topic and create a Keyword search (at least 10) around your defined area of Research Interest/Topic [10pts]
Conduct a Literature Search based on information relevant to your topic. [20pts]]
Identify at least 10 sources, e.g. peer reviewed journals, conference papers & proceedings, conference journals, technical report/documents, trade journal, government doc, engineering news, etc.)
Use APA reference and citation format. Create an Annotated Bibliography from 5 of your identified sources (Max 1/2 for each source). */ ** [20pts]
Prepare 2 pages. Consider and explain how it fits in with the UN Sustainability goals or the engineering grand challenge agenda. [40pts] Instructions [Formating]: [10pts] Organize your responses clearly and neatly; Each question response must be clearly identified; Submit in Word only – Use Times Roman 11 Font
Note – Include all sources, all urls must be hyperlinked!
Use APA reference and citation format. Cite “Chat Gpt” if used.
Include filename (e.g. PJames-Information & Databases)
Define the current gain factor in the connection common emitter and explain how it is calculated from the output characteristics of the transistor. – Potrebno je definirati faktor pojačanja struje u zajedničkom emiteru veze i objasniti kako se on izračunava iz izlazne karakteristike tranzistora.
I need all the answers to this so I can study it. I find it easier knowing the answer and being able to see how it was done rather than brainstorming through a million different ways til I get it right.
I left attached a conversation from the group if you think it will help.. (you don’t need to read everything). I left what is already done in the report, I would just like to try to improve it. TABLE OF CONTENTS
INTRODUCTION
GENERAL AND SPECIFIC OBJECTIVES
MATERIALS USED (this part is not needed)
METHODOLOGY
DISCUSSION AND RESULTS (this part is not needed)
CONCLUSION
REFERENCES
Perhaps the part about general and specific objectives… and for the methodology, I thought about explaining in general how a submarine works, the flotation system that uses density, explaining the challenges of communication with the submarine underwater, since water absorbs radio waves. We didn’t define the project’s justification very well, so we could try to elaborate on that. Maybe discuss the importance of submarines in nuclear warfare.
can you revised our lab report by expiring yourself from this one only modify the introduction by explaining our approach which will look the same and the methodology and fixed our result and discussion .. don’t deleted our add any pictures just fixed it as the other and that’s would be all ..
don’t copy and paste exactly ( plagiarism) what they said but explain the same thing in different words using different references because we are in the same lab .. I will attach the lab instructions so you can know what is it about and our lab ( the one to be revised and the one you need to inspired yourself with )
can you revised our lab report by expiring yourself from this one only modify the introduction by explaining our approach which will look the same and the methodology and fixed our result and discussion .. don’t deleted our add any pictures just fixed it as the other and that’s would be all ..
don’t copy and paste exactly ( plagiarism) what they said but explain the same thing in different words using different references because we are in the same lab .. I will attach the lab instructions so you can know what is it about and our lab ( the one to be revised and the one you need to inspired yourself with )